Replacing the springs on your garage door is not a very complicated job after all.
Manufacturers use these springs on almost all openers today. You have probably seen one of them hanging around your garage already. They are really cheap to buy so replacing an old spring with a new one is actually quite easy and straight forward since you won't need any special tools or equipment to do this job right.
Garage door repairs can also be made if the garage door motor stops working the roller door. If your garage door springs break roller doors or you have broken garage door springs, replacing it would be the best to avoid serious injury.
Regular maintenance for tilt door springs and sectional door springs can help the bottom corners from further damage if they happen to break or fall on opening.To begin with, open up the cover that protects the inner workings of your opener by simply pulling it off or unscrewing 2-4 screws holding it in place if there are no visible hinges involved. The type of garage door opener you have will determine how easy this part will be for you.
As soon as the cover is removed, you should see the broken spring hanging in place or lying on top of the drum. If it's still attached to the door itself, use your screwdriver to push down one end of both wire clips so they are no longer locked in their track holes.
The old spring wire should slide right off at this point or when pushed with a pair of needle-nose pliers. The replacement process is basically the same for both situations. Just unwind the spring on the new one, lock it in place with the wire clip and wind it up just like its predecessor. On some openers, you need to remove a small metal strap wrapped around both springs that keep them together before winding them up all over again.
It costs about $35 to $60 to replace the spring on a typical garage door. You will get the best price if you buy everything needed for the repair from a local hardware store. Materials include two springs, one to replace the broken one and another spare just in case something happens, later on, 2 wire clips that lock them into place, a new metal strap that keeps both of these things together and screws for mounting all of them on the door.
Replacing the springs on your garage door is not that complicated of a job. You will need to pick up some spare ones for this price range but these are actually easy to find online. The only real issue you might face will be choosing between extension and torsion springs, which one you need for your particular door model.
Extensions springs are there to replace broken or worn-out coil springs and in some cases do the job better than the original ones. Both of them go all around your drums and they're very heavy duty in most cases. A standard garage door opener can't lift more than 100 lbs with a pair of these on each side so when you start approaching 200 or 300 lbs, you will either need two separate openers for this job or extensions springs on both sides of your door.
Torsion springs are there to lift the door itself and they work in a completely different way than extension or coil springs. This is why you will need an entirely different opener unit for this type of installation. Torsion springs come either wound up all the way or in some cases, pre-wound so it's pretty much ready to use right out of the box. These setups are the best choice if your garage door is extremely heavy since these can support weights over a hundred kilos.
Replacing them on your own is actually pretty easy but if you feel like you're not up for this, there's no shame in calling a professional garage door repair company. They will do the job right and most importantly, they know what they're doing.
Yes, the springs on your garage door can be replaced by you. If you can operate basic tools and have some mechanical knowledge it should not be too big of an issue for you. It's the easiest part of the replacement from the entire system.
All you need to do is examine them closely and figure out which one snapped so next time your opener starts screeching, you will know what needs fixing immediately. If you are renting in New South Wales, the upkeep may not be your sole responsibility. Check with your local regulations.It depends on the type of spring to be replaced. If it's torsion spring, this job will likely take a few hours since they're not easy to install and you have to do everything by yourself without any help from another person. On the other hand, if it's an extension or coil spring that needs replacement, this can be done in about 20 minutes or so. You don't actually have to remove anything from the door itself so once you figure out where these are located, changing them should be pretty simple even for a complete amateur who had no previous experience with garage door repair.
Exact measurements are not always necessary but you should be well aware of what your door weight limit is before choosing replacement ones so don't underestimate this particular step since bigger isn't always better! You can find these dimensions listed on any manual you have for your garage door opener or by looking at the specifications section on our website and we recommend taking down those numbers and checking them with the new ones before placing an order online. Overweight garage doors can become a serious safety hazard and besides, they won't last as long as they should if you keep on using coils or torsion springs on them all the time.
Replacing garage door springs does not require any special tools and in most cases, standard ones will get the job done. You will need the below.
Vice grips.
Tape measure.
Screwdriver.
Socket wrenches.
Removing broken springs is not a very hard process but you have to be very careful when dealing with torsion ones since they can snap back at you when removed from the door and if that happens, it can cause serious injuries. Always wear safety goggles and use some protective gear before attempting this.
Use a socket wrench to remove bolts holding cables in place. Once you get them off, carefully unwind the cables and eye on one side so it's easier for you to pull out both of your garage door springs. Place them aside so they don't get damaged while you work on replacing them with new ones.
If after removing broken ones there's still tension on cables, you'll have to release this with a screwdriver. Insert new springs and connect them to previously removed cables. If you unwound cables completely, rewind them around the drums the same way they were before. This is where a vice grip comes in handy. Reattach bolts, lubricate any part that needs it and make sure all is secure.